In the Linux kernel, the following vulnerability has been resolved: bonding: restore bond's IFF_SLAVE flag if a non-eth dev enslave fails syzbot reported a warning[1] where the bond device itself is a slave and we try to enslave a non-ethernet device as the first slave which fails but then in the error path when ether_setup() restores the bond device it also clears all flags. In my previous fix[2] I restored the IFF_MASTER flag, but I didn't consider the case that the bond device itself might also be a slave with IFF_SLAVE set, so we need to restore that flag as well. Use the bond_ether_setup helper which does the right thing and restores the bond's flags properly. Steps to reproduce using a nlmon dev: $ ip l add nlmon0 type nlmon $ ip l add bond1 type bond $ ip l add bond2 type bond $ ip l set bond1 master bond2 $ ip l set dev nlmon0 master bond1 $ ip -d l sh dev bond1 22: bond1: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noqueue master bond2 state DOWN mode DEFAULT group default qlen 1000 (now bond1's IFF_SLAVE flag is gone and we'll hit a warning[3] if we try to delete it) [1] https://syzkaller.appspot.com/bug?id=391c7b1f6522182899efba27d891f1743e8eb3ef [2] commit 7d5cd2ce5292 ("bonding: correctly handle bonding type change on enslave failure") [3] example warning: [ 27.008664] bond1: (slave nlmon0): The slave device specified does not support setting the MAC address [ 27.008692] bond1: (slave nlmon0): Error -95 calling set_mac_address [ 32.464639] bond1 (unregistering): Released all slaves [ 32.464685] ------------[ cut here ]------------ [ 32.464686] WARNING: CPU: 1 PID: 2004 at net/core/dev.c:10829 unregister_netdevice_many+0x72a/0x780 [ 32.464694] Modules linked in: br_netfilter bridge bonding virtio_net [ 32.464699] CPU: 1 PID: 2004 Comm: ip Kdump: loaded Not tainted 5.18.0-rc3+ #47 [ 32.464703] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.1-2.fc37 04/01/2014 [ 32.464704] RIP: 0010:unregister_netdevice_many+0x72a/0x780 [ 32.464707] Code: 99 fd ff ff ba 90 1a 00 00 48 c7 c6 f4 02 66 96 48 c7 c7 20 4d 35 96 c6 05 fa c7 2b 02 01 e8 be 6f 4a 00 0f 0b e9 73 fd ff ff <0f> 0b e9 5f fd ff ff 80 3d e3 c7 2b 02 00 0f 85 3b fd ff ff ba 59 [ 32.464710] RSP: 0018:ffffa006422d7820 EFLAGS: 00010206 [ 32.464712] RAX: ffff8f6e077140a0 RBX: ffffa006422d7888 RCX: 0000000000000000 [ 32.464714] RDX: ffff8f6e12edbe58 RSI: 0000000000000296 RDI: ffffffff96d4a520 [ 32.464716] RBP: ffff8f6e07714000 R08: ffffffff96d63600 R09: ffffa006422d7728 [ 32.464717] R10: 0000000000000ec0 R11: ffffffff9698c988 R12: ffff8f6e12edb140 [ 32.464719] R13: dead000000000122 R14: dead000000000100 R15: ffff8f6e12edb140 [ 32.464723] FS: 00007f297c2f1740(0000) GS:ffff8f6e5d900000(0000) knlGS:0000000000000000 [ 32.464725] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 32.464726] CR2: 00007f297bf1c800 CR3: 00000000115e8000 CR4: 0000000000350ee0 [ 32.464730] Call Trace: [ 32.464763] <TASK> [ 32.464767] rtnl_dellink+0x13e/0x380 [ 32.464776] ? cred_has_capability.isra.0+0x68/0x100 [ 32.464780] ? __rtnl_unlock+0x33/0x60 [ 32.464783] ? bpf_lsm_capset+0x10/0x10 [ 32.464786] ? security_capable+0x36/0x50 [ 32.464790] rtnetlink_rcv_msg+0x14e/0x3b0 [ 32.464792] ? _copy_to_iter+0xb1/0x790 [ 32.464796] ? post_alloc_hook+0xa0/0x160 [ 32.464799] ? rtnl_calcit.isra.0+0x110/0x110 [ 32.464802] netlink_rcv_skb+0x50/0xf0 [ 32.464806] netlink_unicast+0x216/0x340 [ 32.464809] netlink_sendmsg+0x23f/0x480 [ 32.464812] sock_sendmsg+0x5e/0x60 [ 32.464815] ____sys_sendmsg+0x22c/0x270 [ 32.464818] ? import_iovec+0x17/0x20 [ 32.464821] ? sendmsg_copy_msghdr+0x59/0x90 [ 32.464823] ? do_set_pte+0xa0/0xe0 [ 32.464828] ___sys_sendmsg+0x81/0xc0 [ 32.464832] ? mod_objcg_state+0xc6/0x300 [ 32.464835] ? refill_obj_stock+0xa9/0x160 [ 32.464838] ? memcg_slab_free_hook+0x1a5/0x1f0 [ 32.464842] __sys_sendm ---truncated---

linux

An issue was discovered on goTenna Mesh devices with app 5.5.3 and firmware 1.1.12. It uses a custom implementation of encryption without any additional integrity checking mechanisms. This leaves messages malleable to an attacker that can access the message.

gotenna

An issue was discovered on goTenna v1 devices with app 5.5.3 and firmware 0.25.5. The app uses a custom implementation of encryption without any additional integrity checking mechanisms. This leaves messages malleable to an attacker that can access the message.

gotenna

In the Linux kernel, the following vulnerability has been resolved: net/smc: Fix possible leaked pernet namespace in smc_init() In smc_init(), register_pernet_subsys(&smc_net_stat_ops) is called without any error handling. If it fails, registering of &smc_net_ops won't be reverted. And if smc_nl_init() fails, &smc_net_stat_ops itself won't be reverted. This leaves wild ops in subsystem linkedlist and when another module tries to call register_pernet_operations() it triggers page fault: BUG: unable to handle page fault for address: fffffbfff81b964c RIP: 0010:register_pernet_operations+0x1b9/0x5f0 Call Trace: <TASK> register_pernet_subsys+0x29/0x40 ebtables_init+0x58/0x1000 [ebtables] ...

linux

A vulnerability was found in Apereo CAS 5.2.6 and classified as critical. Affected by this issue is the function saveService of the file cas-5.2.6\webapp-mgmt\cas-management-webapp-support\src\main\java\org\apereo\cas\mgmt\services\web\RegisteredServiceSimpleFormController.java of the component Groovy Code Handler. The manipulation leads to code injection. The attack may be launched remotely. The complexity of an attack is rather high. The exploitation is known to be difficult. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

apereo

In the Linux kernel, the following vulnerability has been resolved: ext4: fix OOB read when checking dotdot dir Mounting a corrupted filesystem with directory which contains '.' dir entry with rec_len == block size results in out-of-bounds read (later on, when the corrupted directory is removed). ext4_empty_dir() assumes every ext4 directory contains at least '.' and '..' as directory entries in the first data block. It first loads the '.' dir entry, performs sanity checks by calling ext4_check_dir_entry() and then uses its rec_len member to compute the location of '..' dir entry (in ext4_next_entry). It assumes the '..' dir entry fits into the same data block. If the rec_len of '.' is precisely one block (4KB), it slips through the sanity checks (it is considered the last directory entry in the data block) and leaves "struct ext4_dir_entry_2 *de" point exactly past the memory slot allocated to the data block. The following call to ext4_check_dir_entry() on new value of de then dereferences this pointer which results in out-of-bounds mem access. Fix this by extending __ext4_check_dir_entry() to check for '.' dir entries that reach the end of data block. Make sure to ignore the phony dir entries for checksum (by checking name_len for non-zero). Note: This is reported by KASAN as use-after-free in case another structure was recently freed from the slot past the bound, but it is really an OOB read. This issue was found by syzkaller tool. Call Trace: [ 38.594108] BUG: KASAN: slab-use-after-free in __ext4_check_dir_entry+0x67e/0x710 [ 38.594649] Read of size 2 at addr ffff88802b41a004 by task syz-executor/5375 [ 38.595158] [ 38.595288] CPU: 0 UID: 0 PID: 5375 Comm: syz-executor Not tainted 6.14.0-rc7 #1 [ 38.595298] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 [ 38.595304] Call Trace: [ 38.595308] <TASK> [ 38.595311] dump_stack_lvl+0xa7/0xd0 [ 38.595325] print_address_description.constprop.0+0x2c/0x3f0 [ 38.595339] ? __ext4_check_dir_entry+0x67e/0x710 [ 38.595349] print_report+0xaa/0x250 [ 38.595359] ? __ext4_check_dir_entry+0x67e/0x710 [ 38.595368] ? kasan_addr_to_slab+0x9/0x90 [ 38.595378] kasan_report+0xab/0xe0 [ 38.595389] ? __ext4_check_dir_entry+0x67e/0x710 [ 38.595400] __ext4_check_dir_entry+0x67e/0x710 [ 38.595410] ext4_empty_dir+0x465/0x990 [ 38.595421] ? __pfx_ext4_empty_dir+0x10/0x10 [ 38.595432] ext4_rmdir.part.0+0x29a/0xd10 [ 38.595441] ? __dquot_initialize+0x2a7/0xbf0 [ 38.595455] ? __pfx_ext4_rmdir.part.0+0x10/0x10 [ 38.595464] ? __pfx___dquot_initialize+0x10/0x10 [ 38.595478] ? down_write+0xdb/0x140 [ 38.595487] ? __pfx_down_write+0x10/0x10 [ 38.595497] ext4_rmdir+0xee/0x140 [ 38.595506] vfs_rmdir+0x209/0x670 [ 38.595517] ? lookup_one_qstr_excl+0x3b/0x190 [ 38.595529] do_rmdir+0x363/0x3c0 [ 38.595537] ? __pfx_do_rmdir+0x10/0x10 [ 38.595544] ? strncpy_from_user+0x1ff/0x2e0 [ 38.595561] __x64_sys_unlinkat+0xf0/0x130 [ 38.595570] do_syscall_64+0x5b/0x180 [ 38.595583] entry_SYSCALL_64_after_hwframe+0x76/0x7e

linux

In JotUrl 2.0, passwords are sent via HTTP GET-type requests, potentially exposing credentials to eavesdropping or insecure records.

joturl

Cleartext transmission of sensitive information issue exists in Wi-Fi AP UNIT 'AC-WPS-11ac series'. If exploited, a man-in-the-middle attack may allow a remote unauthenticated attacker to eavesdrop the communication and obtain the authentication information.

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Unconditionally save+flush host FPSIMD/SVE/SME state There are several problems with the way hyp code lazily saves the host's FPSIMD/SVE state, including: * Host SVE being discarded unexpectedly due to inconsistent configuration of TIF_SVE and CPACR_ELx.ZEN. This has been seen to result in QEMU crashes where SVE is used by memmove(), as reported by Eric Auger: https://issues.redhat.com/browse/RHEL-68997 * Host SVE state is discarded *after* modification by ptrace, which was an unintentional ptrace ABI change introduced with lazy discarding of SVE state. * The host FPMR value can be discarded when running a non-protected VM, where FPMR support is not exposed to a VM, and that VM uses FPSIMD/SVE. In these cases the hyp code does not save the host's FPMR before unbinding the host's FPSIMD/SVE/SME state, leaving a stale value in memory. Avoid these by eagerly saving and "flushing" the host's FPSIMD/SVE/SME state when loading a vCPU such that KVM does not need to save any of the host's FPSIMD/SVE/SME state. For clarity, fpsimd_kvm_prepare() is removed and the necessary call to fpsimd_save_and_flush_cpu_state() is placed in kvm_arch_vcpu_load_fp(). As 'fpsimd_state' and 'fpmr_ptr' should not be used, they are set to NULL; all uses of these will be removed in subsequent patches. Historical problems go back at least as far as v5.17, e.g. erroneous assumptions about TIF_SVE being clear in commit: 8383741ab2e773a9 ("KVM: arm64: Get rid of host SVE tracking/saving") ... and so this eager save+flush probably needs to be backported to ALL stable trees.

linux

A path traversal vulnerability exists in stitionai/devika, specifically in the project creation functionality. In the affected version beacf6edaa205a5a5370525407a6db45137873b3, the project name is not validated, allowing an attacker to create a project with a crafted name that traverses directories. This can lead to arbitrary file overwrite when the application generates code and saves it to the specified project directory, potentially resulting in remote code execution.

A CSRF vulnerability exists in comfyanonymous/comfyui versions up to v0.2.2. This vulnerability allows attackers to host malicious websites that, when visited by authenticated ComfyUI users, can perform arbitrary API requests on behalf of the user. This can be exploited to perform actions such as uploading arbitrary files via the `/upload/image` endpoint. The lack of CSRF protections on API endpoints like `/upload/image`, `/prompt`, and `/history` leaves users vulnerable to unauthorized actions, which could be combined with other vulnerabilities such as stored-XSS to further compromise user sessions.

comfy

In danny-avila/librechat version v0.7.5-rc2, a vulnerability exists in the preset creation functionality where a user can manipulate the user ID field through mass assignment. This allows an attacker to inject a different user ID into the preset object, causing the preset to appear in the UI of another user. The vulnerability arises because the backend saves the entire object received without validating the attributes and their values, impacting both integrity and confidentiality.

librechat

The Product Input Fields for WooCommerce plugin for WordPress is vulnerable to arbitrary file uploads due to insufficient file type validation in the add_product_input_fields_to_order_item_meta() function in all versions up to, and including, 1.12.0. This may make it possible for unauthenticated attackers to upload arbitrary files on the affected site's server which may make remote code execution possible. Please note that by default the plugin is only vulnerable to a double extension file upload attack, unless an administrators leaves the accepted file extensions field blank which can make .php file uploads possible. Please note 1.12.2 was mistakenly marked as patched while 1.12.1 was marked as vulnerable for a short period of time, this is not the case and 1.12.1 is fully patched.

tychesoftwares

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Load DR6 with guest value only before entering .vcpu_run() loop Move the conditional loading of hardware DR6 with the guest's DR6 value out of the core .vcpu_run() loop to fix a bug where KVM can load hardware with a stale vcpu->arch.dr6. When the guest accesses a DR and host userspace isn't debugging the guest, KVM disables DR interception and loads the guest's values into hardware on VM-Enter and saves them on VM-Exit. This allows the guest to access DRs at will, e.g. so that a sequence of DR accesses to configure a breakpoint only generates one VM-Exit. For DR0-DR3, the logic/behavior is identical between VMX and SVM, and also identical between KVM_DEBUGREG_BP_ENABLED (userspace debugging the guest) and KVM_DEBUGREG_WONT_EXIT (guest using DRs), and so KVM handles loading DR0-DR3 in common code, _outside_ of the core kvm_x86_ops.vcpu_run() loop. But for DR6, the guest's value doesn't need to be loaded into hardware for KVM_DEBUGREG_BP_ENABLED, and SVM provides a dedicated VMCB field whereas VMX requires software to manually load the guest value, and so loading the guest's value into DR6 is handled by {svm,vmx}_vcpu_run(), i.e. is done _inside_ the core run loop. Unfortunately, saving the guest values on VM-Exit is initiated by common x86, again outside of the core run loop. If the guest modifies DR6 (in hardware, when DR interception is disabled), and then the next VM-Exit is a fastpath VM-Exit, KVM will reload hardware DR6 with vcpu->arch.dr6 and clobber the guest's actual value. The bug shows up primarily with nested VMX because KVM handles the VMX preemption timer in the fastpath, and the window between hardware DR6 being modified (in guest context) and DR6 being read by guest software is orders of magnitude larger in a nested setup. E.g. in non-nested, the VMX preemption timer would need to fire precisely between #DB injection and the #DB handler's read of DR6, whereas with a KVM-on-KVM setup, the window where hardware DR6 is "dirty" extends all the way from L1 writing DR6 to VMRESUME (in L1). L1's view: ========== <L1 disables DR interception> CPU 0/KVM-7289 [023] d.... 2925.640961: kvm_entry: vcpu 0 A: L1 Writes DR6 CPU 0/KVM-7289 [023] d.... 2925.640963: <hack>: Set DRs, DR6 = 0xffff0ff1 B: CPU 0/KVM-7289 [023] d.... 2925.640967: kvm_exit: vcpu 0 reason EXTERNAL_INTERRUPT intr_info 0x800000ec D: L1 reads DR6, arch.dr6 = 0 CPU 0/KVM-7289 [023] d.... 2925.640969: <hack>: Sync DRs, DR6 = 0xffff0ff0 CPU 0/KVM-7289 [023] d.... 2925.640976: kvm_entry: vcpu 0 L2 reads DR6, L1 disables DR interception CPU 0/KVM-7289 [023] d.... 2925.640980: kvm_exit: vcpu 0 reason DR_ACCESS info1 0x0000000000000216 CPU 0/KVM-7289 [023] d.... 2925.640983: kvm_entry: vcpu 0 CPU 0/KVM-7289 [023] d.... 2925.640983: <hack>: Set DRs, DR6 = 0xffff0ff0 L2 detects failure CPU 0/KVM-7289 [023] d.... 2925.640987: kvm_exit: vcpu 0 reason HLT L1 reads DR6 (confirms failure) CPU 0/KVM-7289 [023] d.... 2925.640990: <hack>: Sync DRs, DR6 = 0xffff0ff0 L0's view: ========== L2 reads DR6, arch.dr6 = 0 CPU 23/KVM-5046 [001] d.... 3410.005610: kvm_exit: vcpu 23 reason DR_ACCESS info1 0x0000000000000216 CPU 23/KVM-5046 [001] ..... 3410.005610: kvm_nested_vmexit: vcpu 23 reason DR_ACCESS info1 0x0000000000000216 L2 => L1 nested VM-Exit CPU 23/KVM-5046 [001] ..... 3410.005610: kvm_nested_vmexit_inject: reason: DR_ACCESS ext_inf1: 0x0000000000000216 CPU 23/KVM-5046 [001] d.... 3410.005610: kvm_entry: vcpu 23 CPU 23/KVM-5046 [001] d.... 3410.005611: kvm_exit: vcpu 23 reason VMREAD CPU 23/KVM-5046 [001] d.... 3410.005611: kvm_entry: vcpu 23 CPU 23/KVM-5046 [001] d.... 3410. ---truncated---

linux

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix hang during unmount when block group reclaim task is running When we start an unmount, at close_ctree(), if we have the reclaim task running and in the middle of a data block group relocation, we can trigger a deadlock when stopping an async reclaim task, producing a trace like the following: [629724.498185] task:kworker/u16:7 state:D stack: 0 pid:681170 ppid: 2 flags:0x00004000 [629724.499760] Workqueue: events_unbound btrfs_async_reclaim_metadata_space [btrfs] [629724.501267] Call Trace: [629724.501759] <TASK> [629724.502174] __schedule+0x3cb/0xed0 [629724.502842] schedule+0x4e/0xb0 [629724.503447] btrfs_wait_on_delayed_iputs+0x7c/0xc0 [btrfs] [629724.504534] ? prepare_to_wait_exclusive+0xc0/0xc0 [629724.505442] flush_space+0x423/0x630 [btrfs] [629724.506296] ? rcu_read_unlock_trace_special+0x20/0x50 [629724.507259] ? lock_release+0x220/0x4a0 [629724.507932] ? btrfs_get_alloc_profile+0xb3/0x290 [btrfs] [629724.508940] ? do_raw_spin_unlock+0x4b/0xa0 [629724.509688] btrfs_async_reclaim_metadata_space+0x139/0x320 [btrfs] [629724.510922] process_one_work+0x252/0x5a0 [629724.511694] ? process_one_work+0x5a0/0x5a0 [629724.512508] worker_thread+0x52/0x3b0 [629724.513220] ? process_one_work+0x5a0/0x5a0 [629724.514021] kthread+0xf2/0x120 [629724.514627] ? kthread_complete_and_exit+0x20/0x20 [629724.515526] ret_from_fork+0x22/0x30 [629724.516236] </TASK> [629724.516694] task:umount state:D stack: 0 pid:719055 ppid:695412 flags:0x00004000 [629724.518269] Call Trace: [629724.518746] <TASK> [629724.519160] __schedule+0x3cb/0xed0 [629724.519835] schedule+0x4e/0xb0 [629724.520467] schedule_timeout+0xed/0x130 [629724.521221] ? lock_release+0x220/0x4a0 [629724.521946] ? lock_acquired+0x19c/0x420 [629724.522662] ? trace_hardirqs_on+0x1b/0xe0 [629724.523411] __wait_for_common+0xaf/0x1f0 [629724.524189] ? usleep_range_state+0xb0/0xb0 [629724.524997] __flush_work+0x26d/0x530 [629724.525698] ? flush_workqueue_prep_pwqs+0x140/0x140 [629724.526580] ? lock_acquire+0x1a0/0x310 [629724.527324] __cancel_work_timer+0x137/0x1c0 [629724.528190] close_ctree+0xfd/0x531 [btrfs] [629724.529000] ? evict_inodes+0x166/0x1c0 [629724.529510] generic_shutdown_super+0x74/0x120 [629724.530103] kill_anon_super+0x14/0x30 [629724.530611] btrfs_kill_super+0x12/0x20 [btrfs] [629724.531246] deactivate_locked_super+0x31/0xa0 [629724.531817] cleanup_mnt+0x147/0x1c0 [629724.532319] task_work_run+0x5c/0xa0 [629724.532984] exit_to_user_mode_prepare+0x1a6/0x1b0 [629724.533598] syscall_exit_to_user_mode+0x16/0x40 [629724.534200] do_syscall_64+0x48/0x90 [629724.534667] entry_SYSCALL_64_after_hwframe+0x44/0xae [629724.535318] RIP: 0033:0x7fa2b90437a7 [629724.535804] RSP: 002b:00007ffe0b7e4458 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6 [629724.536912] RAX: 0000000000000000 RBX: 00007fa2b9182264 RCX: 00007fa2b90437a7 [629724.538156] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000555d6cf20dd0 [629724.539053] RBP: 0000555d6cf20ba0 R08: 0000000000000000 R09: 00007ffe0b7e3200 [629724.539956] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 [629724.540883] R13: 0000555d6cf20dd0 R14: 0000555d6cf20cb0 R15: 0000000000000000 [629724.541796] </TASK> This happens because: 1) Before entering close_ctree() we have the async block group reclaim task running and relocating a data block group; 2) There's an async metadata (or data) space reclaim task running; 3) We enter close_ctree() and park the cleaner kthread; 4) The async space reclaim task is at flush_space() and runs all the existing delayed iputs; 5) Before the async space reclaim task calls btrfs_wait_on_delayed_iputs(), the block group reclaim task which is doing the data block group relocation, creates a delayed iput at replace_file_extents() (called when COWing leaves that have file extent items pointing to relocated data exten ---truncated---

linux

In the Linux kernel, the following vulnerability has been resolved: powerpc/papr_scm: Fix leaking nvdimm_events_map elements Right now 'char *' elements allocated for individual 'stat_id' in 'papr_scm_priv.nvdimm_events_map[]' during papr_scm_pmu_check_events(), get leaked in papr_scm_remove() and papr_scm_pmu_register(), papr_scm_pmu_check_events() error paths. Also individual 'stat_id' arent NULL terminated 'char *' instead they are fixed 8-byte sized identifiers. However papr_scm_pmu_register() assumes it to be a NULL terminated 'char *' and at other places it assumes it to be a 'papr_scm_perf_stat.stat_id' sized string which is 8-byes in size. Fix this by allocating the memory for papr_scm_priv.nvdimm_events_map to also include space for 'stat_id' entries. This is possible since number of available events/stat_ids are known upfront. This saves some memory and one extra level of indirection from 'nvdimm_events_map' to 'stat_id'. Also rest of the code can continue to call 'kfree(papr_scm_priv.nvdimm_events_map)' without needing to iterate over the array and free up individual elements.

linux

In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: gadget: Replace list_for_each_entry_safe() if using giveback The list_for_each_entry_safe() macro saves the current item (n) and the item after (n+1), so that n can be safely removed without corrupting the list. However, when traversing the list and removing items using gadget giveback, the DWC3 lock is briefly released, allowing other routines to execute. There is a situation where, while items are being removed from the cancelled_list using dwc3_gadget_ep_cleanup_cancelled_requests(), the pullup disable routine is running in parallel (due to UDC unbind). As the cleanup routine removes n, and the pullup disable removes n+1, once the cleanup retakes the DWC3 lock, it references a request who was already removed/handled. With list debug enabled, this leads to a panic. Ensure all instances of the macro are replaced where gadget giveback is used. Example call stack: Thread#1: __dwc3_gadget_ep_set_halt() - CLEAR HALT -> dwc3_gadget_ep_cleanup_cancelled_requests() ->list_for_each_entry_safe() ->dwc3_gadget_giveback(n) ->dwc3_gadget_del_and_unmap_request()- n deleted[cancelled_list] ->spin_unlock ->Thread#2 executes ... ->dwc3_gadget_giveback(n+1) ->Already removed! Thread#2: dwc3_gadget_pullup() ->waiting for dwc3 spin_lock ... ->Thread#1 released lock ->dwc3_stop_active_transfers() ->dwc3_remove_requests() ->fetches n+1 item from cancelled_list (n removed by Thread#1) ->dwc3_gadget_giveback() ->dwc3_gadget_del_and_unmap_request()- n+1 deleted[cancelled_list] ->spin_unlock

linux

An access to an uninitialized pointer flaw was found in X.Org and Xwayland. The function compCheckRedirect() may fail if it cannot allocate the backing pixmap. In that case, compRedirectWindow() will return a BadAlloc error without validating the window tree marked just before, which leaves the validated data partly initialized and the use of an uninitialized pointer later.

tigervnc · x.org · redhat

smartbanner.js is a customizable smart app banner for iOS and Android. Prior to version 1.14.1, clicking on smartbanner `View` link and navigating to 3rd party page leaves `window.opener` exposed. It may allow hostile third parties to abuse `window.opener`, e.g. by redirection or injection on the original page with smartbanner. `rel="noopener"` is automatically populated to links as of `v1.14.1` which is a recommended upgrade to resolve the vulnerability. Some workarounds are available for those who cannot upgrade. Ensure `View` link is only taking users to App Store or Google Play Store where security is guarded by respective app store security teams. If `View` link is going to a third party page, limit smartbanner.js to be used on iOS that decreases the scope of the vulnerability since as of Safari 12.1, `rel="noopener"` is imposed on all `target="_blank"` links. Version 1.14.1 of smartbanner.js contains a fix for the issue.

The administrative web interface of a Netgear C7800 Router running firmware version 6.01.07 (and possibly others) authenticates users via basic authentication, with an HTTP header containing a base64 value of the plaintext username and password. Because the web server also does not utilize transport security by default, this renders the administrative credentials vulnerable to eavesdropping by an adversary during every authenticated request made by a client to the router over a WLAN, or a LAN, should the adversary be able to perform a man-in-the-middle attack.

netgear

When etcupdate encounters conflicts while merging files, it saves a version containing conflict markers in /var/db/etcupdate/conflicts. This version does not preserve the mode of the input file, and is world-readable. This applies to files that would normally have restricted visibility, such as /etc/master.passwd. An unprivileged local user may be able to read encrypted root and user passwords from the temporary master.passwd file created in /var/db/etcupdate/conflicts. This is possible only when conflicts within the password file arise during an update, and the unprotected file is deleted when conflicts are resolved.

In the Linux kernel, the following vulnerability has been resolved: iio: light: vcnl4035: fix information leak in triggered buffer The 'buffer' local array is used to push data to userspace from a triggered buffer, but it does not set an initial value for the single data element, which is an u16 aligned to 8 bytes. That leaves at least 4 bytes uninitialized even after writing an integer value with regmap_read(). Initialize the array to zero before using it to avoid pushing uninitialized information to userspace.

linux

All versions of ETIC Telecom Remote Access Server (RAS) prior to 4.5.0 are vulnerable to reflected cross site scripting in the appliance site name. The ETIC RAS web server saves the site name and then presents it to the administrators in a few different pages.

etictelecom