In the Linux kernel, the following vulnerability has been resolved: ipv6: validate extension header length before copying to cmsg ip6_datagram_recv_specific_ctl() builds IPV6_{HOPOPTS,DSTOPTS,RTHDR} cmsgs (and their IPV6_2292* legacy counterparts) by trusting the on-wire hdrlen byte (ptr[1]) when computing the put_cmsg() length. The length was validated only at parse time (ipv6_parse_hopopts(), etc.). An nftables payload-write expression can rewrite hdrlen after parsing and before the skb reaches recvmsg; the write itself is in-bounds but put_cmsg() then reads up to ((hdrlen+1) << 3) = 2040 bytes from an 8-byte header. nftables is reachable from an unprivileged user namespace, so this is an unprivileged slab-out-of-bounds read: BUG: KASAN: slab-out-of-bounds in put_cmsg+0x3ac/0x540 put_cmsg+0x3ac/0x540 udpv6_recvmsg+0xca0/0x1250 sock_recvmsg+0xdf/0x190 ____sys_recvmsg+0x1b1/0x620 Add ipv6_get_exthdr_len() which validates that at least two bytes are accessible before reading the hdrlen field, then checks the computed length against skb_tail_pointer(skb), returning 0 on failure. Extension headers are kept in the linear skb area by pskb_may_pull() during input, so skb_tail_pointer() is the correct bound. Use ipv6_get_exthdr_len() at all non-AH call sites: the five standalone cmsg blocks (HbH, 2292HbH, 2292DSTOPTS x2, 2292RTHDR) and the three standard cases in the extension-header walk loop (DSTOPTS, ROUTING, default). AH retains an inline bounds check because its length formula differs ((ptr[1]+2)<<2). The walk loop also gets a pre-read bounds check at the top to validate ptr before any case accesses ptr[0] or ptr[1]. When the walk loop detects a corrupted header, return from the function instead of continuing to process later socket options.

Impact: @fastify/http-proxy versions up to and including 11.5.0 fail to rewrite the request prefix when the prefix segment is URL-encoded. Fastify's router URL-decodes paths for route matching, but request.url retains the original encoded form, and the prefix-rewrite step uses a literal string replace against the decoded prefix. A request that encodes one or more characters of the configured prefix therefore matches the route but skips the rewrite, so the raw encoded path is forwarded to the upstream unchanged. The upstream then decodes the path and serves it, letting an attacker reach upstream paths that the proxy was configured to hide via rewritePrefix, including internal or administrative endpoints. Patches: upgrade to @fastify/http-proxy 11.6.0. Workarounds: none.

fastify

view_component is a framework for building reusable, testable, and encapsulated view components in Ruby on Rails. From 4.0.0 until 4.12.0, ViewComponent::Base instances retain render-scoped objects across calls to render_in; if the same component, collection, or spacer component instance is reused across requests, users, tenants, or threads, later renders can use stale helpers, controller, request, view_flow, format/variant details, and slot child context from an earlier render. This can cause authorization-aware components to render privileged UI for a lower-privileged user, generate links using a stale Host header, leak slot/helper state, and mix request context under concurrent rendering. This issue is fixed in version 4.12.0.

viewcomponent

h2o is an HTTP server with support for HTTP/1.x, HTTP/2 and HTTP/3. Prior to commit 9265bdd, there is an HTTP/2 state amplification issue that combines HPACK decompression amplification with Slowloris-style stream stalling. Amplified decoded header state can be retained by stalled HTTP/2 streams, and depending on the configuration, additional limits are needed to bound decoded header state and prevent attack. This issue has been fixed by commit 9265bdd.

h2o

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix same-register dst/src OOB read and pointer leak in sock_ops When a BPF sock_ops program accesses ctx fields with dst_reg == src_reg, the SOCK_OPS_GET_SK() and SOCK_OPS_GET_FIELD() macros fail to zero the destination register in the !fullsock / !locked_tcp_sock path. Both macros borrow a temporary register to check is_fullsock / is_locked_tcp_sock when dst_reg == src_reg, because dst_reg holds the ctx pointer. When the check is false (e.g., TCP_NEW_SYN_RECV state with a request_sock), dst_reg should be zeroed but is not, leaving the stale ctx pointer: - SOCK_OPS_GET_SK: dst_reg retains the ctx pointer, passes NULL checks as PTR_TO_SOCKET_OR_NULL, and can be used as a bogus socket pointer, leading to stack-out-of-bounds access in helpers like bpf_skc_to_tcp6_sock(). - SOCK_OPS_GET_FIELD: dst_reg retains the ctx pointer which the verifier believes is a SCALAR_VALUE, leaking a kernel pointer. Fix both macros by: - Changing JMP_A(1) to JMP_A(2) in the fullsock path to skip the added instruction. - Adding BPF_MOV64_IMM(si->dst_reg, 0) after the temp register restore in the !fullsock path, placed after the restore because dst_reg == src_reg means we need src_reg intact to read ctx->temp.

linux

Netty is a network application framework for development of protocol servers and clients. Prior to versions 4.1.135.Final and 4.2.15.Final, the RedisArrayAggregator handler permanently leaks pooled direct-memory buffers when a Redis pipeline connection closes before a RESP array aggregate completes. The handler retains child messages in per-handler state (`depths` field) but defines no `channelInactive`, `handlerRemoved`, or `exceptionCaught` method to release them when the pipeline tears down. Because the leaked buffers are slices of `PooledByteBufAllocator` chunks, they prevent those chunks from being returned to the JVM-wide direct-memory pool. Repeated connection churn by any network peer monotonically drains this shared pool, eventually causing allocation failures on all Netty channels in the process. Versions 4.1.135.Final and 4.2.15.Final patch the issue.

netty

Netty is a network application framework for development of protocol servers and clients. Prior to versions 4.1.135.Final and 4.2.15.Final, SslClientHelloHandler.decode() reads the 24-bit TLS handshake length and, when the ClientHello does not fit in the first record, eagerly allocates `ctx.alloc().buffer(handshakeLength)` (line 161). The guard at line 140 is `handshakeLength > maxClientHelloLength && maxClientHelloLength != 0`, and the commonly-used SniHandler/AbstractSniHandler constructors (SniHandler(Mapping), SniHandler(AsyncMapping), AbstractSniHandler()) pass maxClientHelloLength=0 and handshakeTimeoutMillis=0, so the length guard is disabled and no timeout is scheduled. A 16 MiB request exceeds the default pooled chunk size and becomes a huge/unpooled allocation performed immediately. The buffer is retained in the handler until the channel closes. Versions 4.1.135.Final and 4.2.15.Final patch the issue.

netty

Netty is a network application framework for development of protocol servers and clients. In netty-codec-haproxy prior to versions 4.1.135.Final and 4.2.15.Final, when decoding a PP2_TYPE_SSL TLV, HAProxyMessage.readNextTLV() first calls `header.retainedSlice(header.readerIndex(), length)` and only then reads the 1-byte client field and 4-byte verify field. If the attacker sets the TLV length below 5, the subsequent readByte/readInt throws IndexOutOfBoundsException. HAProxyMessageDecoder only catches HAProxyProtocolException around this call, so the IOOBE propagates and the retained slice on the pooled cumulation buffer is never released. Versions 4.1.135.Final and 4.2.15.Final patch the issue.

netty

Spring Data's internal property-lookup cache accepts and permanently retains attacker-supplied strings as cache keys, allowing heap exhaustion through repeated requests. Affected versions: Spring Data Commons 2.7.0 through 2.7.19; 3.3.0 through 3.3.16; 3.4.0 through 3.4.14; 3.5.0 through 3.5.11; 4.0.0 through 4.0.5.

7-Zip is a file archiver with a high compression ratio. Versions 9.21 through 26.00 contain an An uninitialized memory disclosure vulnerability in the UEFI capsule (.scap) parser in 7-Zip. The OpenCapsule function allocates a heap buffer of attacker-declared CapsuleImageSize (up to 1 GiB) without zero-initialization, then reads the file contents into it with ReadStream_FALSE whose return value is silently discarded. If the file is truncated, the unread tail of the buffer retains uninitialized heap memory, which is then exposed as extracted file content via GetStream. Version 26.0.1 fixes the issue.

7-zip

FreeScout is a free help desk and shared inbox built with PHP's Laravel framework. Prior to 1.8.221, FreeScout allows a non-admin user to permanently delete an internal note (private thread) from any conversation, even after that user's access to the mailbox containing the conversation has been revoked. The ThreadPolicy::delete authorization policy does not verify mailbox membership, so a former team member retains destructive write access to notes they created. This vulnerability is fixed in 1.8.221.

n8n-MCP is an MCP server that provides AI assistants access to n8n node documentation, properties, and operations. Prior to 2.51.3, the workflow telemetry sanitizer could retain partial fragments of URL-shaped node parameters before sending workflow data to the project's anonymous telemetry backend. Values placed in HTTP-Request-style node parameters — such as customer or tenant identifiers, short secrets embedded in query strings, and signed request parameters — could therefore appear in stored telemetry, contrary to the collection boundary documented in PRIVACY.md. This vulnerability is fixed in 2.51.3.

An issue was discovered in Canonical Multipass for macOS before version 1.16.3 due to an incomplete fix for CVE-2025-5199. While the patch in version 1.16.0 updated the ownership of the multipassd daemon binary to root:wheel, five co-located binaries (multipass, qemu-img, qemu-system-aarch64, qemu-system-x86_64, and sshfs_server) in /Library/Application Support/com.canonical.multipass/bin/ retain ownership by the installing user and remain writable. Because the root LaunchDaemon (com.canonical.multipassd.plist) configures a PATH environment variable that prioritizes this user-writable directory and invokes these auxiliary binaries by their bare names, a local attacker can replace an auxiliary binary (such as qemu-img) with a malicious wrapper. When the root daemon subsequently triggers the binary during routine execution (e.g., via multipass launch), the malicious code executes with root privileges, leading to local privilege escalation.

In the Linux kernel, the following vulnerability has been resolved: spi: microchip-core-qspi: control built-in cs manually The coreQSPI IP supports only a single chip select, which is automagically operated by the hardware - set low when the transmit buffer first gets written to and set high when the number of bytes written to the TOTALBYTES field of the FRAMES register have been sent on the bus. Additional devices must use GPIOs for their chip selects. It was reported to me that if there are two devices attached to this QSPI controller that the in-built chip select is set low while linux tries to access the device attached to the GPIO. This went undetected as the boards that connected multiple devices to the SPI controller all exclusively used GPIOs for chip selects, not relying on the built-in chip select at all. It turns out that this was because the built-in chip select, when controlled automagically, is set low when active and high when inactive, thereby ruling out its use for active-high devices or devices that need to transmit with the chip select disabled. Modify the driver so that it controls chip select directly, retaining the behaviour for mem_ops of setting the chip select active for the entire duration of the transfer in the exec_op callback. For regular transfers, implement the set_cs callback for the core to use. As part of this, the existing setup callback, mchp_coreqspi_setup_op(), is removed. Modifying the CLKIDLE field is not safe to do during operation when there are multiple devices, so this code is removed entirely. Setting the MASTER and ENABLE fields is something that can be done once at probe, it doesn't need to be re-run for each device. Instead the new setup callback sets the built-in chip select to its inactive state for active-low devices, as the reset value of the chip select in software controlled mode is low.

linux

In the Linux kernel, the following vulnerability has been resolved: net: rtnetlink: zero ifla_vf_broadcast to avoid stack infoleak in rtnl_fill_vfinfo rtnl_fill_vfinfo() declares struct ifla_vf_broadcast on the stack without initialisation: struct ifla_vf_broadcast vf_broadcast; The struct contains a single fixed 32-byte field: /* include/uapi/linux/if_link.h */ struct ifla_vf_broadcast { __u8 broadcast[32]; }; The function then copies dev->broadcast into it using dev->addr_len as the length: memcpy(vf_broadcast.broadcast, dev->broadcast, dev->addr_len); On Ethernet devices (the overwhelming majority of SR-IOV NICs) dev->addr_len is 6, so only the first 6 bytes of broadcast[] are written. The remaining 26 bytes retain whatever was previously on the kernel stack. The full struct is then handed to userspace via: nla_put(skb, IFLA_VF_BROADCAST, sizeof(vf_broadcast), &vf_broadcast) leaking up to 26 bytes of uninitialised kernel stack per VF per RTM_GETLINK request, repeatable. The other vf_* structs in the same function are explicitly zeroed for exactly this reason - see the memset() calls for ivi, vf_vlan_info, node_guid and port_guid a few lines above. vf_broadcast was simply missed when it was added. Reachability: any unprivileged local process can open AF_NETLINK / NETLINK_ROUTE without capabilities and send RTM_GETLINK with an IFLA_EXT_MASK attribute carrying RTEXT_FILTER_VF. The kernel walks each VF and emits IFLA_VF_BROADCAST, leaking 26 bytes of stack per VF per request. Stack residue at this call site can include return addresses and transient sensitive data; KASAN with stack instrumentation, or KMSAN, will flag the nla_put() when reproduced. Zero the on-stack struct before the partial memcpy, matching the existing pattern used for the other vf_* structs in the same function.

In the Linux kernel, the following vulnerability has been resolved: pseries/papr-hvpipe: Fix null ptr deref in papr_hvpipe_dev_create_handle() commit 6d3789d347a7 ("papr-hvpipe: convert papr_hvpipe_dev_create_handle() to FD_PREPARE()"), changed the create handle to FD_PREPARE(), but it caused kernel null-ptr-deref because after call to retain_and_null_ptr(src_info), src_info is re-used for adding it to the global list. Getting the following kernel panic in papr_hvpipe_dev_create_handle() when trying to add src_info to the list. Kernel attempted to write user page (0) - exploit attempt? (uid: 0) BUG: Kernel NULL pointer dereference on write at 0x00000000 Faulting instruction address: 0xc0000000001b44a0 Oops: Kernel access of bad area, sig: 11 [#1] ... Call Trace: papr_hvpipe_dev_ioctl+0x1f4/0x48c (unreliable) sys_ioctl+0x528/0x1064 system_call_exception+0x128/0x360 system_call_vectored_common+0x15c/0x2ec Now, the error handling with FD_PREPARE's file cleanup and __free(kfree) auto cleanup is getting too convoluted. This is mainly because we need to ensure only 1 user get the srcID handle. To simplify this, we allocate prepare the src_info in the beginning and add it to the global list under a spinlock after checking that no duplicates exist. This simplify the error handling where if the FD_ADD fails, we can simply remove the src_info from the list and consume any pending msg in hvpipe to be cleared, after src_info became visible in the global list.

Vulnerable to DNS rebinding attacks when using SSE (http://b/499408790). During the beta phase, we implemented `allowed-origins` and `allowed-hosts` flags to align with MCP security guidelines. However, the hardcoded `Access-Control-Allow-Origin: *` header in the SSE initialization handler was inadvertently retained. This vulnerability specifically impacts users connecting via Toolbox using SSE under specification v2024-11-05.

Budibase is an open-source low-code platform. Prior to 3.38.2, the public API role unassignment endpoint (POST /api/public/v1/roles/unassign) updates user documents in CouchDB but does not invalidate the corresponding Redis user cache entries. Because the authentication middleware resolves user identity and permissions from this cache (TTL: 3600 seconds), a user whose admin, builder, or app-level roles have been revoked via the public API retains those privileges for up to 1 hour. This vulnerability is fixed in 3.38.2.

In the Linux kernel, the following vulnerability has been resolved: fbdev: udlfb: add vm_ops to dlfb_ops_mmap to prevent use-after-free dlfb_ops_mmap() uses remap_pfn_range() to map vmalloc framebuffer pages to userspace but sets no vm_ops on the VMA. This means the kernel cannot track active mmaps. When dlfb_realloc_framebuffer() replaces the backing buffer via FBIOPUT_VSCREENINFO, existing mmap PTEs are not invalidated. On USB disconnect, dlfb_ops_destroy() calls vfree() on the old pages while userspace PTEs still reference them, resulting in a use-after-free: the process retains read/write access to freed kernel pages. Add vm_operations_struct with open/close callbacks that maintain an atomic mmap_count on struct dlfb_data. In dlfb_realloc_framebuffer(), check mmap_count and return -EBUSY if the buffer is currently mapped, preventing buffer replacement while userspace holds stale PTEs. Tested with PoC using dummy_hcd + raw_gadget USB device emulation.

Authentication modules in Netatalk 1.5.0 through 4.4.2 fail to check the return value of seteuid(), which may allow a remote authenticated attacker to retain elevated privileges under error conditions.

libheif is a HEIF and AVIF file format decoder and encoder. In versions 1.21.2 and prior, when decoding a HEIF grid image with strict_decoding=false (the default), a corrupted tile silently fails to decode and the library returns heif_error_Ok with no indication of failure, leading to an uninitialized heap memory information leak. The canvas is allocated via create_clone_image_at_new_size() → plane.alloc() → new (std::nothrow) uint8_t[allocation_size] which does not zero the memory; only the alpha plane is explicitly initialized via fill_plane(), so the Y, Cb, and Cr planes contain whatever was previously at that heap address. The failed tile's region of the canvas is never written. It retains uninitialized heap data that is delivered to the caller as decoded pixel values (4,096 bytes per Y/Cb/Cr plane = 12,288+ bytes total). Any application using libheif to decode grid-based HEIF/AVIF files with default settings is vulnerable: a crafted .heic or .avif file causes 4,096+ bytes of heap memory to appear as pixel values in the decoded image, and the calling application receives heif_error_Ok, so it has no indication the output contains heap garbage. In server-side image processing, an uploaded crafted HEIF decoded and re-encoded (e.g., as PNG/JPEG for thumbnails, CDN, social media) can leak cross-user data such as auth tokens, database results, and other users' image data. This issue has been fixed in version 1.22.0.

Open WebUI is a self-hosted artificial intelligence platform designed to operate entirely offline. Prior to 0.9.0, the is_user_channel_member function checks whether a ChannelMember row exists but does not check the is_active field. When a user is deactivated from a group or DM channel (removed by the channel owner, or leaves voluntarily), their membership row persists with is_active=False and status='left'. Because the authorization check ignores this field, the deactivated user retains full read and write access to the channel via direct API calls. This vulnerability is fixed in 0.9.0.

openwebui

Open WebUI is a self-hosted artificial intelligence platform designed to operate entirely offline. Prior to 0.9.0, administrative role changes and user deletions do not iterate SESSION_POOL to disconnect affected sessions. As a result, a user whose admin role has been revoked retains admin privileges within their existing Socket.IO session for as long as they keep the connection alive (via automatic heartbeats). The gap is exclusive to the Socket.IO session cache. This vulnerability is fixed in 0.9.0.

openwebui