An Improper Locking vulnerability in the GTP plugin of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (Dos). If an SRX Series device receives a specifically malformed GPRS Tunnelling Protocol (GTP) Modify Bearer Request message, a lock is acquired and never released. This results in other threads not being able to acquire a lock themselves, causing a watchdog timeout leading to FPC crash and restart. This issue leads to a complete traffic outage until the device has automatically recovered. This issue affects Junos OS on SRX Series: * all versions before 22.4R3-S8, * 23.2 versions before 23.2R2-S5, * 23.4 versions before 23.4R2-S6, * 24.2 versions before 24.2R2-S3, * 24.4 versions before 24.4R2-S2, * 25.2 versions before 25.2R1-S1, 25.2R2.

juniper

A Time-of-check Time-of-use (TOCTOU) Race Condition vulnerability in the method to collect FPC Ethernet firmware statistics of Juniper Networks Junos OS on MX10k Series allows a local, low-privileged attacker executing the 'show system firmware' CLI command to cause an LC480 or LC2101 line card to reset. On MX10k Series systems with LC480 or LC2101 line cards, repeated execution of the 'show system firmware' CLI command can cause the line card to crash and restart. Additionally, some time after the line card crashes, chassisd may also crash and restart, generating a core dump.This issue affects Junos OS on MX10k Series:  * all versions before 21.2R3-S10,  * from 21.4 before 21.4R3-S9,  * from 22.2 before 22.2R3-S7,  * from 22.4 before 22.4R3-S6,  * from 23.2 before 23.2R2-S2,  * from 23.4 before 23.4R2-S3,  * from 24.2 before 24.2R2.

juniper

An Incorrect Calculation vulnerability in the Layer 2 Control Protocol Daemon (l2cpd) of Juniper Networks Junos OS Evolved allows an unauthenticated network-adjacent attacker flapping the management interface to cause the learning of new MACs over label-switched interfaces (LSI) to stop while generating a flood of logs, resulting in high CPU usage. When the issue is seen, the following log message will be generated: op:1 flag:0x6 mac:xx:xx:xx:xx:xx:xx bd:2 ifl:13302 reason:0(REASON_NONE) i-op:6(INTRNL_OP_HW_FORCE_DELETE) status:10 lstatus:10 err:26(GETIFBD_VALIDATE_FAILED) err-reason 4(IFBD_VALIDATE_FAIL_EPOCH_MISMATCH) hw_wr:0x4 ctxsync:0 fwdsync:0 rtt-id:51 p_ifl:0 fwd_nh:0 svlbnh:0 event:- smask:0x100000000 dmask:0x0 mplsmask 0x1 act:0x5800 extf:0x0 pfe-id 0 hw-notif-ifl 13302 programmed-ifl 4294967295 pseudo-vtep underlay-ifl-idx 0 stack:GET_MAC, ALLOCATE_MAC, GET_IFL, GET_IFF, GET_IFBD, STOP, This issue affects Junos OS Evolved:  * all versions before 21.4R3-S7-EVO,  * from 22.2 before 22.2R3-S4-EVO,  * from 22.3 before 22.3R3-S3-EVO,  * from 22.4 before 22.4R3-S2-EVO,  * from 23.2 before 23.2R2-S1-EVO,  * from 23.4 before 23.4R1-S2-EVO, 23.4R2-EVO.

juniper

An Improper Check for Unusual or Exceptional Conditions vulnerability in the packet forwarding engine (PFE) of Juniper Networks Junos OS on EX4k Series and QFX5k Series platforms allows an unauthenticated network-adjacent attacker flapping an interface to cause traffic between VXLAN Network Identifiers (VNIs) to drop, leading to a Denial of Service (DoS). On all EX4k and QFX5k platforms, a link flap in an EVPN-VXLAN configuration Link Aggregation Group (LAG) results in Inter-VNI traffic dropping when there are multiple load-balanced next-hop routes for the same destination. This issue is only applicable to systems that support EVPN-VXLAN Virtual Port-Link Aggregation Groups (VPLAG), such as the QFX5110, QFX5120, QFX5200, EX4100, EX4300, EX4400, and EX4650. Service can only be restored by restarting the affected FPC via the 'request chassis fpc restart slot <slot-number>' command. This issue affects Junos OS on EX4k and QFX5k Series:  * all versions before 21.4R3-S12,  * all versions of 22.2 * from 22.4 before 22.4R3-S8,  * from 23.2 before 23.2R2-S5,  * from 23.4 before 23.4R2-S5,  * from 24.2 before 24.2R2-S3, * from 24.4 before 24.4R2.

juniper

An Improper Handling of Exceptional Conditions vulnerability in the packet forwarding engine (PFE) of Juniper Networks Junos OS on SRX Series allows an unauthenticated network-based attacker sending a specific ICMP packet through a GRE tunnel to cause the PFE to crash and restart. When PowerMode IPsec (PMI) and GRE performance acceleration are enabled and the device receives a specific ICMP packet, a crash occurs in the SRX PFE, resulting in traffic loss. PMI is enabled by default, and GRE performance acceleration can be enabled by running the configuration command shown below. PMI is a mode of operation that provides IPsec performance improvements using Vector Packet Processing. Note that PMI with GRE performance acceleration is only supported on specific SRX platforms. This issue affects Junos OS on the SRX Series: * all versions before 21.4R3-S12,  * from 22.4 before 22.4R3-S8,  * from 23.2 before 23.2R2-S5,  * from 23.4 before 23.4R2-S5,  * from 24.2 before 24.2R2-S3,  * from 24.4 before 24.4R2-S1,  * from 25.2 before 25.2R1-S1, 25.2R2.

juniper

A Loop with Unreachable Exit Condition ('Infinite Loop') vulnerability in the SIP application layer gateway (ALG) of Juniper Networks Junos OS on SRX Series and MX Series with MX-SPC3 or MS-MPC allows an unauthenticated network-based attacker sending specific SIP messages over TCP to crash the flow management process, leading to a Denial of Service (DoS). On SRX Series, and MX Series with MX-SPC3 or MS-MPC service cards, receipt of multiple SIP messages causes the SIP headers to be parsed incorrectly, eventually causing a continuous loop and leading to a watchdog timer expiration, crashing the flowd process on SRX Series and MX Series with MX-SPC3, or mspmand process on MX Series with MS-MPC. This issue only occurs over TCP. SIP messages sent over UDP cannot trigger this issue. This issue affects Junos OS on SRX Series and MX Series with MX-SPC3 and MS-MPC: * all versions before 21.2R3-S10,  * from 21.4 before 21.4R3-S12,  * from 22.4 before 22.4R3-S8,  * from 23.2 before 23.2R2-S5,  * from 23.4 before 23.4R2-S6,  * from 24.2 before 24.2R2-S3,  * from 24.4 before 24.4R2-S1,  * from 25.2 before 25.2R1-S1, 25.2R2.

juniper

A Stack-based Buffer Overflow vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS allows a network-based attacker, authenticated with low privileges to cause a Denial-of-Service (DoS). Subscribing to telemetry sensors at scale causes all FPC connections to drop, resulting in an FPC crash and restart. The issue was not seen when YANG packages for the specific sensors were installed. This issue affects Junos OS:  * all versions before 22.4R3-S7, * 23.2 version before 23.2R2-S4, * 23.4 versions before 23.4R2.

juniper

An Improper Handling of Exceptional Conditions vulnerability in packet processing of Juniper Networks Junos OS allows an unauthenticated, network-adjacent attacker sending a specifically malformed ICMP packet to cause an FPC to crash and restart, resulting in a Denial of Service (DoS). When an ICMP packet is received with a specifically malformed IP header value, the FPC receiving the packet crashes and restarts. Due to the specific type of malformed packet, adjacent upstream routers would not forward the packet, limiting the attack surface to adjacent networks. This issue only affects ICMPv4. ICMPv6 is not vulnerable to this issue. This issue does not affect AFT-based line cards such as the MPC10, MPC11, LC4800, LC9600, and MX304. This issue affects Junos OS:  * all versions before 21.2R3-S9,  * from 21.4 before 21.4R3-S10,  * from 22.2 before 22.2R3-S7,  * from 22.3 before 22.3R3-S4,  * from 22.4 before 22.4R3-S5,  * from 23.2 before 23.2R2-S3,  * from 23.4 before 23.4R2-S3,  * from 24.2 before 24.2R1-S2, 24.2R2.

juniper

An Improper Check for Unusual or Exceptional Conditions vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause an availability impact for downstream devices. When an affected device receives a specific optional, transitive BGP attribute over an existing BGP session, it will be erroneously modified before propagation to peers. When the attribute is detected as malformed by the peers, these peers will most likely terminate the BGP sessions with the affected devices and thereby cause an availability impact due to the resulting routing churn. This issue affects: Junos OS: * all versions before 22.4R3-S8, * 23.2 versions before 23.2R2-S5 * 23.4 versions before 23.4R2-S6, * 24.2 versions before 24.2R2-S2, * 24.4 versions before 24.4R2; Junos OS Evolved:  * all versions before 22.4R3-S8-EVO, * 23.2 versions before 23.2R2-S5-EVO, * 23.4 versions before 23.4R2-S6-EVO, * 24.2 versions before 24.2R2-S2-EVO, * 24.4 versions before 24.4R2-EVO.

juniper

A NULL Pointer Dereference vulnerability in the chassis daemon (chassisd) of Juniper Networks Junos OS on MX, SRX and EX Series allows a local attacker with low privileges to cause a Denial-of-Service (DoS). When a user executes the 'show chassis' command with specifically crafted options, chassisd will crash and restart. Due to this all components but the Routing Engine (RE) in the chassis are reinitialized, which leads to a complete service outage, which the system automatically recovers from. This issue affects: Junos OS on MX, SRX and EX Series, except MX10000 Series and MX304:  * all versions before 22.4R3-S8, * 23.2 versions before 23.2R2-S5, * 23.4 versions before 23.4R2-S6, * 24.2 versions before 24.2R2-S2, * 24.4 versions before 24.4R2.

juniper

A Buffer Over-read vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). When an affected device receives a BGP update with a set of specific optional transitive attributes over an established peering session, rpd will crash and restart when attempting to advertise the received information to another peer. This issue can only happen if one or both of the BGP peers of the receiving session are non-4-byte-AS capable as determined from the advertised capabilities during BGP session establishment. Junos OS and Junos OS Evolved default behavior is 4-byte-AS capable unless this has been specifically disabled by configuring: [ protocols bgp ... disable-4byte-as ] Established BGP sessions can be checked by executing: show bgp neighbor <IP address> | match "4 byte AS" This issue affects: Junos OS:  * all versions before 22.4R3-S8, * 23.2 versions before 23.2R2-S5, * 23.4 versions before 23.4R2-S6, * 24.2 versions before 24.2R2-S2, * 24.4 versions before 24.4R2; Junos OS Evolved:  * all versions before 22.4R3-S8-EVO, * 23.2 versions before 23.2R2-S5-EVO, * 23.4 versions before 23.4R2-S6-EVO, * 24.2 versions before 24.2R2-S2-EVO, * 24.4 versions before 24.4R2-EVO.

juniper

An Incorrect Permission Assignment for Critical Resource vulnerability in the Juniper DHCP daemon (jdhcpd) of Juniper Networks Junos OS and Junos OS Evolved allows a local, low-privileged user to write to the Unix socket used to manage the jdhcpd process, resulting in complete control over the resource. This vulnerability allows any low-privileged user logged into the system to connect to the Unix socket and issue commands to manage the DHCP service, in essence, taking administrative control of the local DHCP server or DHCP relay. This issue affects: Junos OS: * all versions before 21.2R3-S10, * all versions of 22.2, * from 21.4 before 21.4R3-S12, * from 22.4 before 22.4R3-S8, * from 23.2 before 23.2R2-S5, * from 23.4 before 23.4R2-S6, * from 24.2 before 24.2R2-S2, * from 24.4 before 24.4R2, * from 25.2 before 25.2R1-S1, 25.2R2; Junos OS Evolved: * all versions before 22.4R3-S8-EVO, * from 23.2 before 23.2R2-S5-EVO, * from 23.4 before 23.4R2-S6-EVO, * from 24.2 before 24.2R2-S2-EVO, * from 24.4 before 24.4R2-EVO, * from 25.2 before 25.2R1-S1-EVO, 25.2R2-EVO.

juniper

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Juniper DHCP service (jdhcpd) of Juniper Networks Junos OS and Junos OS Evolved allows a DHCP client in one subnet to exhaust the address pools of other subnets, leading to a Denial of Service (DoS) on the downstream DHCP server. By default, the DHCP relay agent inserts its own Option 82 information when forwarding client requests, optionally replacing any Option 82 information provided by the client. When a specific DHCP DISCOVER is received in 'forward-only' mode with Option 82, the device should drop the message unless 'trust-option82' is configured. Instead, the DHCP relay forwards these packets to the DHCP server unmodified, which uses up addresses in the DHCP server's address pool, ultimately leading to address pool exhaustion. This issue affects Junos OS:  * all versions before 21.2R3-S10, * from 21.4 before 21.4R3-S12, * all versions of 22.2, * from 22.4 before 22.4R3-S8,  * from 23.2 before 23.2R2-S5,  * from 23.4 before 23.4R2-S6,  * from 24.2 before 24.2R2-S2,  * from 24.4 before 24.4R2,  * from 25.2 before 25.2R1-S1, 25.2R2. Junos OS Evolved: * all versions before 21.4R3-S12-EVO,  * all versions of 22.2-EVO, * from 22.4 before 22.4R3-S8-EVO,  * from 23.2 before 23.2R2-S5-EVO,  * from 23.4 before 23.4R2-S6-EVO,  * from 24.2 before 24.2R2-S2-EVO,  * from 24.4 before 24.4R2-EVO,  * from 25.2 before 25.2R1-S1-EVO, 25.2R2-EVO.

juniper

An Untrusted Pointer Dereference vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a local, authenticated attacker with low privileges to cause a Denial-of-Service (DoS). When the command 'show route < ( receive-protocol | advertising-protocol ) bgp > detail' is executed, and at least one of the routes in the intended output has specific attributes, this will cause an rpd crash and restart. 'show route ... extensive' is not affected. This issue affects: Junos OS:  * all versions before 22.4R3-S8, * 23.2 versions before 23.2R2-S5, * 23.4 versions before 23.4R2-S5, * 24.2 versions before 24.2R2-S2, * 24.4 versions before 24.4R2; Junos OS Evolved: * all versions before 22.4R3-S8-EVO,  * 23.2 versions before 23.2R2-S5-EVO, * 23.4 versions before 23.4R2-S6-EVO, * 24.2 versions before 24.2R2-S2-EVO, * 24.4 versions before 24.4R2-EVO.

juniper

In the Linux kernel, the following vulnerability has been resolved: mptcp: ensure context reset on disconnect() After the blamed commit below, if the MPC subflow is already in TCP_CLOSE status or has fallback to TCP at mptcp_disconnect() time, mptcp_do_fastclose() skips setting the `send_fastclose flag` and the later __mptcp_close_ssk() does not reset anymore the related subflow context. Any later connection will be created with both the `request_mptcp` flag and the msk-level fallback status off (it is unconditionally cleared at MPTCP disconnect time), leading to a warning in subflow_data_ready(): WARNING: CPU: 26 PID: 8996 at net/mptcp/subflow.c:1519 subflow_data_ready (net/mptcp/subflow.c:1519 (discriminator 13)) Modules linked in: CPU: 26 UID: 0 PID: 8996 Comm: syz.22.39 Not tainted 6.18.0-rc7-05427-g11fc074f6c36 #1 PREEMPT(voluntary) Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 RIP: 0010:subflow_data_ready (net/mptcp/subflow.c:1519 (discriminator 13)) Code: 90 0f 0b 90 90 e9 04 fe ff ff e8 b7 1e f5 fe 89 ee bf 07 00 00 00 e8 db 19 f5 fe 83 fd 07 0f 84 35 ff ff ff e8 9d 1e f5 fe 90 <0f> 0b 90 e9 27 ff ff ff e8 8f 1e f5 fe 4c 89 e7 48 89 de e8 14 09 RSP: 0018:ffffc9002646fb30 EFLAGS: 00010293 RAX: 0000000000000000 RBX: ffff88813b218000 RCX: ffffffff825c8435 RDX: ffff8881300b3580 RSI: ffffffff825c8443 RDI: 0000000000000005 RBP: 000000000000000b R08: ffffffff825c8435 R09: 000000000000000b R10: 0000000000000005 R11: 0000000000000007 R12: ffff888131ac0000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 FS: 00007f88330af6c0(0000) GS:ffff888a93dd2000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f88330aefe8 CR3: 000000010ff59000 CR4: 0000000000350ef0 Call Trace: <TASK> tcp_data_ready (net/ipv4/tcp_input.c:5356) tcp_data_queue (net/ipv4/tcp_input.c:5445) tcp_rcv_state_process (net/ipv4/tcp_input.c:7165) tcp_v4_do_rcv (net/ipv4/tcp_ipv4.c:1955) __release_sock (include/net/sock.h:1158 (discriminator 6) net/core/sock.c:3180 (discriminator 6)) release_sock (net/core/sock.c:3737) mptcp_sendmsg (net/mptcp/protocol.c:1763 net/mptcp/protocol.c:1857) inet_sendmsg (net/ipv4/af_inet.c:853 (discriminator 7)) __sys_sendto (net/socket.c:727 (discriminator 15) net/socket.c:742 (discriminator 15) net/socket.c:2244 (discriminator 15)) __x64_sys_sendto (net/socket.c:2247) do_syscall_64 (arch/x86/entry/syscall_64.c:63 (discriminator 1) arch/x86/entry/syscall_64.c:94 (discriminator 1)) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) RIP: 0033:0x7f883326702d Address the issue setting an explicit `fastclosing` flag at fastclose time, and checking such flag after mptcp_do_fastclose().

linux

In the Linux kernel, the following vulnerability has been resolved: cpuset: fix warning when disabling remote partition A warning was triggered as follows: WARNING: kernel/cgroup/cpuset.c:1651 at remote_partition_disable+0xf7/0x110 RIP: 0010:remote_partition_disable+0xf7/0x110 RSP: 0018:ffffc90001947d88 EFLAGS: 00000206 RAX: 0000000000007fff RBX: ffff888103b6e000 RCX: 0000000000006f40 RDX: 0000000000006f00 RSI: ffffc90001947da8 RDI: ffff888103b6e000 RBP: ffff888103b6e000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff88810b2e2728 R12: ffffc90001947da8 R13: 0000000000000000 R14: ffffc90001947da8 R15: ffff8881081f1c00 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f55c8bbe0b2 CR3: 000000010b14c000 CR4: 00000000000006f0 Call Trace: <TASK> update_prstate+0x2d3/0x580 cpuset_partition_write+0x94/0xf0 kernfs_fop_write_iter+0x147/0x200 vfs_write+0x35d/0x500 ksys_write+0x66/0xe0 do_syscall_64+0x6b/0x390 entry_SYSCALL_64_after_hwframe+0x4b/0x53 RIP: 0033:0x7f55c8cd4887 Reproduction steps (on a 16-CPU machine): # cd /sys/fs/cgroup/ # mkdir A1 # echo +cpuset > A1/cgroup.subtree_control # echo "0-14" > A1/cpuset.cpus.exclusive # mkdir A1/A2 # echo "0-14" > A1/A2/cpuset.cpus.exclusive # echo "root" > A1/A2/cpuset.cpus.partition # echo 0 > /sys/devices/system/cpu/cpu15/online # echo member > A1/A2/cpuset.cpus.partition When CPU 15 is offlined, subpartitions_cpus gets cleared because no CPUs remain available for the top_cpuset, forcing partitions to share CPUs with the top_cpuset. In this scenario, disabling the remote partition triggers a warning stating that effective_xcpus is not a subset of subpartitions_cpus. Partitions should be invalidated in this case to inform users that the partition is now invalid(cpus are shared with top_cpuset). To fix this issue: 1. Only emit the warning only if subpartitions_cpus is not empty and the effective_xcpus is not a subset of subpartitions_cpus. 2. During the CPU hotplug process, invalidate partitions if subpartitions_cpus is empty.

linux

In the Linux kernel, the following vulnerability has been resolved: mm/page_alloc: change all pageblocks migrate type on coalescing When a page is freed it coalesces with a buddy into a higher order page while possible. When the buddy page migrate type differs, it is expected to be updated to match the one of the page being freed. However, only the first pageblock of the buddy page is updated, while the rest of the pageblocks are left unchanged. That causes warnings in later expand() and other code paths (like below), since an inconsistency between migration type of the list containing the page and the page-owned pageblocks migration types is introduced. [ 308.986589] ------------[ cut here ]------------ [ 308.987227] page type is 0, passed migratetype is 1 (nr=256) [ 308.987275] WARNING: CPU: 1 PID: 5224 at mm/page_alloc.c:812 expand+0x23c/0x270 [ 308.987293] Modules linked in: algif_hash(E) af_alg(E) nft_fib_inet(E) nft_fib_ipv4(E) nft_fib_ipv6(E) nft_fib(E) nft_reject_inet(E) nf_reject_ipv4(E) nf_reject_ipv6(E) nft_reject(E) nft_ct(E) nft_chain_nat(E) nf_nat(E) nf_conntrack(E) nf_defrag_ipv6(E) nf_defrag_ipv4(E) nf_tables(E) s390_trng(E) vfio_ccw(E) mdev(E) vfio_iommu_type1(E) vfio(E) sch_fq_codel(E) drm(E) i2c_core(E) drm_panel_orientation_quirks(E) loop(E) nfnetlink(E) vsock_loopback(E) vmw_vsock_virtio_transport_common(E) vsock(E) ctcm(E) fsm(E) diag288_wdt(E) watchdog(E) zfcp(E) scsi_transport_fc(E) ghash_s390(E) prng(E) aes_s390(E) des_generic(E) des_s390(E) libdes(E) sha3_512_s390(E) sha3_256_s390(E) sha_common(E) paes_s390(E) crypto_engine(E) pkey_cca(E) pkey_ep11(E) zcrypt(E) rng_core(E) pkey_pckmo(E) pkey(E) autofs4(E) [ 308.987439] Unloaded tainted modules: hmac_s390(E):2 [ 308.987650] CPU: 1 UID: 0 PID: 5224 Comm: mempig_verify Kdump: loaded Tainted: G E 6.18.0-gcc-bpf-debug #431 PREEMPT [ 308.987657] Tainted: [E]=UNSIGNED_MODULE [ 308.987661] Hardware name: IBM 3906 M04 704 (z/VM 7.3.0) [ 308.987666] Krnl PSW : 0404f00180000000 00000349976fa600 (expand+0x240/0x270) [ 308.987676] R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:3 PM:0 RI:0 EA:3 [ 308.987682] Krnl GPRS: 0000034980000004 0000000000000005 0000000000000030 000003499a0e6d88 [ 308.987688] 0000000000000005 0000034980000005 000002be803ac000 0000023efe6c8300 [ 308.987692] 0000000000000008 0000034998d57290 000002be00000100 0000023e00000008 [ 308.987696] 0000000000000000 0000000000000000 00000349976fa5fc 000002c99b1eb6f0 [ 308.987708] Krnl Code: 00000349976fa5f0: c020008a02f2 larl %r2,000003499883abd4 00000349976fa5f6: c0e5ffe3f4b5 brasl %r14,0000034997378f60 #00000349976fa5fc: af000000 mc 0,0 >00000349976fa600: a7f4ff4c brc 15,00000349976fa498 00000349976fa604: b9040026 lgr %r2,%r6 00000349976fa608: c0300088317f larl %r3,0000034998800906 00000349976fa60e: c0e5fffdb6e1 brasl %r14,00000349976b13d0 00000349976fa614: af000000 mc 0,0 [ 308.987734] Call Trace: [ 308.987738] [<00000349976fa600>] expand+0x240/0x270 [ 308.987744] ([<00000349976fa5fc>] expand+0x23c/0x270) [ 308.987749] [<00000349976ff95e>] rmqueue_bulk+0x71e/0x940 [ 308.987754] [<00000349976ffd7e>] __rmqueue_pcplist+0x1fe/0x2a0 [ 308.987759] [<0000034997700966>] rmqueue.isra.0+0xb46/0xf40 [ 308.987763] [<0000034997703ec8>] get_page_from_freelist+0x198/0x8d0 [ 308.987768] [<0000034997706fa8>] __alloc_frozen_pages_noprof+0x198/0x400 [ 308.987774] [<00000349977536f8>] alloc_pages_mpol+0xb8/0x220 [ 308.987781] [<0000034997753bf6>] folio_alloc_mpol_noprof+0x26/0xc0 [ 308.987786] [<0000034997753e4c>] vma_alloc_folio_noprof+0x6c/0xa0 [ 308.987791] [<0000034997775b22>] vma_alloc_anon_folio_pmd+0x42/0x240 [ 308.987799] [<000003499777bfea>] __do_huge_pmd_anonymous_page+0x3a/0x210 [ 308.987804] [<00000349976cb0 ---truncated---

linux

In the Linux kernel, the following vulnerability has been resolved: tracing: Do not register unsupported perf events Synthetic events currently do not have a function to register perf events. This leads to calling the tracepoint register functions with a NULL function pointer which triggers: ------------[ cut here ]------------ WARNING: kernel/tracepoint.c:175 at tracepoint_add_func+0x357/0x370, CPU#2: perf/2272 Modules linked in: kvm_intel kvm irqbypass CPU: 2 UID: 0 PID: 2272 Comm: perf Not tainted 6.18.0-ftest-11964-ge022764176fc-dirty #323 PREEMPTLAZY Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.17.0-debian-1.17.0-1 04/01/2014 RIP: 0010:tracepoint_add_func+0x357/0x370 Code: 28 9c e8 4c 0b f5 ff eb 0f 4c 89 f7 48 c7 c6 80 4d 28 9c e8 ab 89 f4 ff 31 c0 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc cc <0f> 0b 49 c7 c6 ea ff ff ff e9 ee fe ff ff 0f 0b e9 f9 fe ff ff 0f RSP: 0018:ffffabc0c44d3c40 EFLAGS: 00010246 RAX: 0000000000000001 RBX: ffff9380aa9e4060 RCX: 0000000000000000 RDX: 000000000000000a RSI: ffffffff9e1d4a98 RDI: ffff937fcf5fd6c8 RBP: 0000000000000001 R08: 0000000000000007 R09: ffff937fcf5fc780 R10: 0000000000000003 R11: ffffffff9c193910 R12: 000000000000000a R13: ffffffff9e1e5888 R14: 0000000000000000 R15: ffffabc0c44d3c78 FS: 00007f6202f5f340(0000) GS:ffff93819f00f000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055d3162281a8 CR3: 0000000106a56003 CR4: 0000000000172ef0 Call Trace: <TASK> tracepoint_probe_register+0x5d/0x90 synth_event_reg+0x3c/0x60 perf_trace_event_init+0x204/0x340 perf_trace_init+0x85/0xd0 perf_tp_event_init+0x2e/0x50 perf_try_init_event+0x6f/0x230 ? perf_event_alloc+0x4bb/0xdc0 perf_event_alloc+0x65a/0xdc0 __se_sys_perf_event_open+0x290/0x9f0 do_syscall_64+0x93/0x7b0 ? entry_SYSCALL_64_after_hwframe+0x76/0x7e ? trace_hardirqs_off+0x53/0xc0 entry_SYSCALL_64_after_hwframe+0x76/0x7e Instead, have the code return -ENODEV, which doesn't warn and has perf error out with: # perf record -e synthetic:futex_wait Error: The sys_perf_event_open() syscall returned with 19 (No such device) for event (synthetic:futex_wait). "dmesg | grep -i perf" may provide additional information. Ideally perf should support synthetic events, but for now just fix the warning. The support can come later.

linux

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Fix VM hard lockup after prolonged inactivity with periodic HV timer When advancing the target expiration for the guest's APIC timer in periodic mode, set the expiration to "now" if the target expiration is in the past (similar to what is done in update_target_expiration()). Blindly adding the period to the previous target expiration can result in KVM generating a practically unbounded number of hrtimer IRQs due to programming an expired timer over and over. In extreme scenarios, e.g. if userspace pauses/suspends a VM for an extended duration, this can even cause hard lockups in the host. Currently, the bug only affects Intel CPUs when using the hypervisor timer (HV timer), a.k.a. the VMX preemption timer. Unlike the software timer, a.k.a. hrtimer, which KVM keeps running even on exits to userspace, the HV timer only runs while the guest is active. As a result, if the vCPU does not run for an extended duration, there will be a huge gap between the target expiration and the current time the vCPU resumes running. Because the target expiration is incremented by only one period on each timer expiration, this leads to a series of timer expirations occurring rapidly after the vCPU/VM resumes. More critically, when the vCPU first triggers a periodic HV timer expiration after resuming, advancing the expiration by only one period will result in a target expiration in the past. As a result, the delta may be calculated as a negative value. When the delta is converted into an absolute value (tscdeadline is an unsigned u64), the resulting value can overflow what the HV timer is capable of programming. I.e. the large value will exceed the VMX Preemption Timer's maximum bit width of cpu_preemption_timer_multi + 32, and thus cause KVM to switch from the HV timer to the software timer (hrtimers). After switching to the software timer, periodic timer expiration callbacks may be executed consecutively within a single clock interrupt handler, because hrtimers honors KVM's request for an expiration in the past and immediately re-invokes KVM's callback after reprogramming. And because the interrupt handler runs with IRQs disabled, restarting KVM's hrtimer over and over until the target expiration is advanced to "now" can result in a hard lockup. E.g. the following hard lockup was triggered in the host when running a Windows VM (only relevant because it used the APIC timer in periodic mode) after resuming the VM from a long suspend (in the host). NMI watchdog: Watchdog detected hard LOCKUP on cpu 45 ... RIP: 0010:advance_periodic_target_expiration+0x4d/0x80 [kvm] ... RSP: 0018:ff4f88f5d98d8ef0 EFLAGS: 00000046 RAX: fff0103f91be678e RBX: fff0103f91be678e RCX: 00843a7d9e127bcc RDX: 0000000000000002 RSI: 0052ca4003697505 RDI: ff440d5bfbdbd500 RBP: ff440d5956f99200 R08: ff2ff2a42deb6a84 R09: 000000000002a6c0 R10: 0122d794016332b3 R11: 0000000000000000 R12: ff440db1af39cfc0 R13: ff440db1af39cfc0 R14: ffffffffc0d4a560 R15: ff440db1af39d0f8 FS: 00007f04a6ffd700(0000) GS:ff440db1af380000(0000) knlGS:000000e38a3b8000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000d5651feff8 CR3: 000000684e038002 CR4: 0000000000773ee0 PKRU: 55555554 Call Trace: <IRQ> apic_timer_fn+0x31/0x50 [kvm] __hrtimer_run_queues+0x100/0x280 hrtimer_interrupt+0x100/0x210 ? ttwu_do_wakeup+0x19/0x160 smp_apic_timer_interrupt+0x6a/0x130 apic_timer_interrupt+0xf/0x20 </IRQ> Moreover, if the suspend duration of the virtual machine is not long enough to trigger a hard lockup in this scenario, since commit 98c25ead5eda ("KVM: VMX: Move preemption timer <=> hrtimer dance to common x86"), KVM will continue using the software timer until the guest reprograms the APIC timer in some way. Since the periodic timer does not require frequent APIC timer register programming, the guest may continue to use the software timer in ---truncated---

linux

Explorer32++ 1.3.5.531 contains a buffer overflow vulnerability in Structured Exception Handler (SEH) records that allows attackers to execute arbitrary code. Attackers can exploit the vulnerability by providing a long file name argument over 396 characters to corrupt the SEH chain and potentially execute malicious code.

explorerplusplus

In the Linux kernel, the following vulnerability has been resolved: scsi: Revert "scsi: qla2xxx: Perform lockless command completion in abort path" This reverts commit 0367076b0817d5c75dfb83001ce7ce5c64d803a9. The commit being reverted added code to __qla2x00_abort_all_cmds() to call sp->done() without holding a spinlock. But unlike the older code below it, this new code failed to check sp->cmd_type and just assumed TYPE_SRB, which results in a jump to an invalid pointer in target-mode with TYPE_TGT_CMD: qla2xxx [0000:65:00.0]-d034:8: qla24xx_do_nack_work create sess success 0000000009f7a79b qla2xxx [0000:65:00.0]-5003:8: ISP System Error - mbx1=1ff5h mbx2=10h mbx3=0h mbx4=0h mbx5=191h mbx6=0h mbx7=0h. qla2xxx [0000:65:00.0]-d01e:8: -> fwdump no buffer qla2xxx [0000:65:00.0]-f03a:8: qla_target(0): System error async event 0x8002 occurred qla2xxx [0000:65:00.0]-00af:8: Performing ISP error recovery - ha=0000000058183fda. BUG: kernel NULL pointer dereference, address: 0000000000000000 PF: supervisor instruction fetch in kernel mode PF: error_code(0x0010) - not-present page PGD 0 P4D 0 Oops: 0010 [#1] SMP CPU: 2 PID: 9446 Comm: qla2xxx_8_dpc Tainted: G O 6.1.133 #1 Hardware name: Supermicro Super Server/X11SPL-F, BIOS 4.2 12/15/2023 RIP: 0010:0x0 Code: Unable to access opcode bytes at 0xffffffffffffffd6. RSP: 0018:ffffc90001f93dc8 EFLAGS: 00010206 RAX: 0000000000000282 RBX: 0000000000000355 RCX: ffff88810d16a000 RDX: ffff88810dbadaa8 RSI: 0000000000080000 RDI: ffff888169dc38c0 RBP: ffff888169dc38c0 R08: 0000000000000001 R09: 0000000000000045 R10: ffffffffa034bdf0 R11: 0000000000000000 R12: ffff88810800bb40 R13: 0000000000001aa8 R14: ffff888100136610 R15: ffff8881070f7400 FS: 0000000000000000(0000) GS:ffff88bf80080000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffffffffd6 CR3: 000000010c8ff006 CR4: 00000000003706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? __die+0x4d/0x8b ? page_fault_oops+0x91/0x180 ? trace_buffer_unlock_commit_regs+0x38/0x1a0 ? exc_page_fault+0x391/0x5e0 ? asm_exc_page_fault+0x22/0x30 __qla2x00_abort_all_cmds+0xcb/0x3e0 [qla2xxx_scst] qla2x00_abort_all_cmds+0x50/0x70 [qla2xxx_scst] qla2x00_abort_isp_cleanup+0x3b7/0x4b0 [qla2xxx_scst] qla2x00_abort_isp+0xfd/0x860 [qla2xxx_scst] qla2x00_do_dpc+0x581/0xa40 [qla2xxx_scst] kthread+0xa8/0xd0 </TASK> Then commit 4475afa2646d ("scsi: qla2xxx: Complete command early within lock") added the spinlock back, because not having the lock caused a race and a crash. But qla2x00_abort_srb() in the switch below already checks for qla2x00_chip_is_down() and handles it the same way, so the code above the switch is now redundant and still buggy in target-mode. Remove it.

In the Linux kernel, the following vulnerability has been resolved: team: fix check for port enabled in team_queue_override_port_prio_changed() There has been a syzkaller bug reported recently with the following trace: list_del corruption, ffff888058bea080->prev is LIST_POISON2 (dead000000000122) ------------[ cut here ]------------ kernel BUG at lib/list_debug.c:59! Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI CPU: 3 UID: 0 PID: 21246 Comm: syz.0.2928 Not tainted syzkaller #0 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 RIP: 0010:__list_del_entry_valid_or_report+0x13e/0x200 lib/list_debug.c:59 Code: 48 c7 c7 e0 71 f0 8b e8 30 08 ef fc 90 0f 0b 48 89 ef e8 a5 02 55 fd 48 89 ea 48 89 de 48 c7 c7 40 72 f0 8b e8 13 08 ef fc 90 <0f> 0b 48 89 ef e8 88 02 55 fd 48 89 ea 48 b8 00 00 00 00 00 fc ff RSP: 0018:ffffc9000d49f370 EFLAGS: 00010286 RAX: 000000000000004e RBX: ffff888058bea080 RCX: ffffc9002817d000 RDX: 0000000000000000 RSI: ffffffff819becc6 RDI: 0000000000000005 RBP: dead000000000122 R08: 0000000000000005 R09: 0000000000000000 R10: 0000000080000000 R11: 0000000000000001 R12: ffff888039e9c230 R13: ffff888058bea088 R14: ffff888058bea080 R15: ffff888055461480 FS: 00007fbbcfe6f6c0(0000) GS:ffff8880d6d0a000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000110c3afcb0 CR3: 00000000382c7000 CR4: 0000000000352ef0 Call Trace: <TASK> __list_del_entry_valid include/linux/list.h:132 [inline] __list_del_entry include/linux/list.h:223 [inline] list_del_rcu include/linux/rculist.h:178 [inline] __team_queue_override_port_del drivers/net/team/team_core.c:826 [inline] __team_queue_override_port_del drivers/net/team/team_core.c:821 [inline] team_queue_override_port_prio_changed drivers/net/team/team_core.c:883 [inline] team_priority_option_set+0x171/0x2f0 drivers/net/team/team_core.c:1534 team_option_set drivers/net/team/team_core.c:376 [inline] team_nl_options_set_doit+0x8ae/0xe60 drivers/net/team/team_core.c:2653 genl_family_rcv_msg_doit+0x209/0x2f0 net/netlink/genetlink.c:1115 genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline] genl_rcv_msg+0x55c/0x800 net/netlink/genetlink.c:1210 netlink_rcv_skb+0x158/0x420 net/netlink/af_netlink.c:2552 genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219 netlink_unicast_kernel net/netlink/af_netlink.c:1320 [inline] netlink_unicast+0x5aa/0x870 net/netlink/af_netlink.c:1346 netlink_sendmsg+0x8c8/0xdd0 net/netlink/af_netlink.c:1896 sock_sendmsg_nosec net/socket.c:727 [inline] __sock_sendmsg net/socket.c:742 [inline] ____sys_sendmsg+0xa98/0xc70 net/socket.c:2630 ___sys_sendmsg+0x134/0x1d0 net/socket.c:2684 __sys_sendmsg+0x16d/0x220 net/socket.c:2716 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xcd/0xfa0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f The problem is in this flow: 1) Port is enabled, queue_id != 0, in qom_list 2) Port gets disabled -> team_port_disable() -> team_queue_override_port_del() -> del (removed from list) 3) Port is disabled, queue_id != 0, not in any list 4) Priority changes -> team_queue_override_port_prio_changed() -> checks: port disabled && queue_id != 0 -> calls del - hits the BUG as it is removed already To fix this, change the check in team_queue_override_port_prio_changed() so it returns early if port is not enabled.

linux