Loading vulnerability details…
361,800
Total CVEs
26,223
Critical
85,816
High
1,626
CISA KEV
88
This Week
28 results · Page 1/2
In the Linux kernel, the following vulnerability has been resolved: net: bcmgenet: keep RBUF EEE/PM disabled Setting RBUF_EEE_EN | RBUF_PM_EN in RBUF_ENERGY_CTRL breaks the RX path on GENET hardware once MAC EEE becomes active. RX traffic stops flowing while the link stays up and the usual descriptor/RX error counters remain quiet. In that state the MAC still accepts frames (rbuf_ovflow_cnt keeps climbing) but RBUF no longer forwards them to DMA, so rx_packets is no longer incremented at the netdev level. On some boards the corruption ends up as a paging fault in skb_release_data via bcmgenet_rx_poll on an LPI exit. Reproduced on Pi 4B (BCM2711 + BCM54213PE) and confirmed by Florian Fainelli on an internal Broadcom 4908-family board with the same crash signature. RBUF_PM_EN is not publicly documented. This shows up more often now that phy_support_eee() enables EEE by default, but it also affects older kernels as soon as TX LPI is turned on via ethtool, so it is not specific to recent changes. Always clear RBUF_EEE_EN | RBUF_PM_EN in bcmgenet_eee_enable_set so the bits stay off across resets. UMAC and TBUF setup is left alone so TX-side EEE keeps working.
In the Linux kernel, the following vulnerability has been resolved: net: bcmgenet: Add a check for oversized packets Occasionnaly we may get oversized packets from the hardware which exceed the nomimal 2KiB buffer size we allocate SKBs with. Add an early check which drops the packet to avoid invoking skb_over_panic() and move on to processing the next packet.
linux
In the Linux kernel, the following vulnerability has been resolved: net: bcmgenet: Use stronger register read/writes to assure ordering GCC12 appears to be much smarter about its dependency tracking and is aware that the relaxed variants are just normal loads and stores and this is causing problems like: [ 210.074549] ------------[ cut here ]------------ [ 210.079223] NETDEV WATCHDOG: enabcm6e4ei0 (bcmgenet): transmit queue 1 timed out [ 210.086717] WARNING: CPU: 1 PID: 0 at net/sched/sch_generic.c:529 dev_watchdog+0x234/0x240 [ 210.095044] Modules linked in: genet(E) nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat] [ 210.146561] ACPI CPPC: PCC check channel failed for ss: 0. ret=-110 [ 210.146927] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G E 5.17.0-rc7G12+ #58 [ 210.153226] CPPC Cpufreq:cppc_scale_freq_workfn: failed to read perf counters [ 210.161349] Hardware name: Raspberry Pi Foundation Raspberry Pi 4 Model B/Raspberry Pi 4 Model B, BIOS EDK2-DEV 02/08/2022 [ 210.161353] pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 210.161358] pc : dev_watchdog+0x234/0x240 [ 210.161364] lr : dev_watchdog+0x234/0x240 [ 210.161368] sp : ffff8000080a3a40 [ 210.161370] x29: ffff8000080a3a40 x28: ffffcd425af87000 x27: ffff8000080a3b20 [ 210.205150] x26: ffffcd425aa00000 x25: 0000000000000001 x24: ffffcd425af8ec08 [ 210.212321] x23: 0000000000000100 x22: ffffcd425af87000 x21: ffff55b142688000 [ 210.219491] x20: 0000000000000001 x19: ffff55b1426884c8 x18: ffffffffffffffff [ 210.226661] x17: 64656d6974203120 x16: 0000000000000001 x15: 6d736e617274203a [ 210.233831] x14: 2974656e65676d63 x13: ffffcd4259c300d8 x12: ffffcd425b07d5f0 [ 210.241001] x11: 00000000ffffffff x10: ffffcd425b07d5f0 x9 : ffffcd4258bdad9c [ 210.248171] x8 : 00000000ffffdfff x7 : 000000000000003f x6 : 0000000000000000 [ 210.255341] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000001000 [ 210.262511] x2 : 0000000000001000 x1 : 0000000000000005 x0 : 0000000000000044 [ 210.269682] Call trace: [ 210.272133] dev_watchdog+0x234/0x240 [ 210.275811] call_timer_fn+0x3c/0x15c [ 210.279489] __run_timers.part.0+0x288/0x310 [ 210.283777] run_timer_softirq+0x48/0x80 [ 210.287716] __do_softirq+0x128/0x360 [ 210.291392] __irq_exit_rcu+0x138/0x140 [ 210.295243] irq_exit_rcu+0x1c/0x30 [ 210.298745] el1_interrupt+0x38/0x54 [ 210.302334] el1h_64_irq_handler+0x18/0x24 [ 210.306445] el1h_64_irq+0x7c/0x80 [ 210.309857] arch_cpu_idle+0x18/0x2c [ 210.313445] default_idle_call+0x4c/0x140 [ 210.317470] cpuidle_idle_call+0x14c/0x1a0 [ 210.321584] do_idle+0xb0/0x100 [ 210.324737] cpu_startup_entry+0x30/0x8c [ 210.328675] secondary_start_kernel+0xe4/0x110 [ 210.333138] __secondary_switched+0x94/0x98 The assumption when these were relaxed seems to be that device memory would be mapped non reordering, and that other constructs (spinlocks/etc) would provide the barriers to assure that packet data and in memory rings/queues were ordered with respect to device register reads/writes. This itself seems a bit sketchy, but the real problem with GCC12 is that it is moving the actual reads/writes around at will as though they were independent operations when in truth they are not, but the compiler can't know that. When looking at the assembly dumps for many of these routines its possible to see very clean, but not strictly in program order operations occurring as the compiler would be free to do if these weren't actually register reads/write operations. Its possible to suppress the timeout with a liberal bit of dma_mb()'s sprinkled around but the device still seems unable to reliably send/receive data. A better plan is to use the safer readl/writel everywhere. Since this partially reverts an older commit, which notes the use of the relaxed variants for performance reasons. I would suggest that any performance problems ---truncated---
linux